Custom made high arch soles are usually made for the the people who have severe cases of low foot arches or complete flat feet. Of course the custom made ones are made from the manufacturers have the specific measurements and such that the flat footed patient will need but what many do not know is that it is possible to create handmade orthotics. The only catch here is that only athletes or people with a mild case of low arch may be able to use it just to be safe.
Now if one would want to make a homemade arch support insole, then he would have to buy a few things. Firstly, he will be needing two to three old insoles that would probably come from an old pair of shoes. He has to make sure that the insoles all have the same size.
The next thing that he would have to get would be a glue that is waterproof or better yet, super glue that can really stick. In order to cut up the insoles, one will be needing a pair of really sharp scissors because insoles may be tough to cut. As long as one has these things, then he may start getting to work on that insole.
So after getting the old insoles, one has to now do a bit of measurements. Always do make sure that all insoles have the same size so that it will be easier to place them on each other. So when one puts one insole on top of the other, he has to find the part that holds the arch of the foot.
Once that part has already been found, then the next thing to do would be to cut out that part using the pair of scissors that was acquired earlier. After that, one has to now make sure that the cut part will match the insole, if not, then maybe a bit more cutting will have to be done. Once that has already been done, then one can now glue the cut part to the insole.
After that has already been done, then one just has to wait for the glue to dry before he tries it out. Of course as stated above, the best glue for this type of project would be super glue. It is this glue that is the stickiest as well as the most effective and it dries really fast.
Now if one would want to make his arch support taller than it already is, he can actually do so by adding another sole part to the insole. Now he has to get the third insole and just what he did a while ago. Once he has done that, he just once again has to let the glue dry and then try to walk with it.
Now making handmade orthotics at home as quite easy as one will be able to see. However, do not try to do this if the flat feet case is quite severe. These handmade ones should only be used for those whose cases are not severe as the severe cases would already need the custom made ones with specific measurements.
Now if one would want to make a homemade arch support insole, then he would have to buy a few things. Firstly, he will be needing two to three old insoles that would probably come from an old pair of shoes. He has to make sure that the insoles all have the same size.
The next thing that he would have to get would be a glue that is waterproof or better yet, super glue that can really stick. In order to cut up the insoles, one will be needing a pair of really sharp scissors because insoles may be tough to cut. As long as one has these things, then he may start getting to work on that insole.
So after getting the old insoles, one has to now do a bit of measurements. Always do make sure that all insoles have the same size so that it will be easier to place them on each other. So when one puts one insole on top of the other, he has to find the part that holds the arch of the foot.
Once that part has already been found, then the next thing to do would be to cut out that part using the pair of scissors that was acquired earlier. After that, one has to now make sure that the cut part will match the insole, if not, then maybe a bit more cutting will have to be done. Once that has already been done, then one can now glue the cut part to the insole.
After that has already been done, then one just has to wait for the glue to dry before he tries it out. Of course as stated above, the best glue for this type of project would be super glue. It is this glue that is the stickiest as well as the most effective and it dries really fast.
Now if one would want to make his arch support taller than it already is, he can actually do so by adding another sole part to the insole. Now he has to get the third insole and just what he did a while ago. Once he has done that, he just once again has to let the glue dry and then try to walk with it.
Now making handmade orthotics at home as quite easy as one will be able to see. However, do not try to do this if the flat feet case is quite severe. These handmade ones should only be used for those whose cases are not severe as the severe cases would already need the custom made ones with specific measurements.
No comments:
Post a Comment